Efficient Marble Quarry Cutting in Namibia: KEENOVA 55kW Wire Saw Machine Working with M002B Diamond Wire

A white marble quarry in Namibia is now running KEENOVA's new-generation 55kW wire saw machines together with M002B diamond wire. The machines have been in production long enough to show how the combination behaves on a real bench — not in a test cut, but in the daily routine of block extraction.
Marble is a forgiving stone to cut and an unforgiving one to cut badly. It is soft and non-abrasive, so the wire can travel faster than it would in granite, and the surface left behind is what the customer eventually sells. That shifts the balance: the wire needs a bond hard enough to survive the stone, and the machine needs enough reserve to keep the wire moving at a steady speed once the cut is deep and the load is constant.
This article records what the site looks like, how the 55kW machines and M002B wire are set up, and what we watch during the first weeks of operation. It describes the application and the reasoning behind the specification. It does not quote production figures for this project, because the quarry keeps its own records and we have not independently verified them.
The site: white marble, dry ground, long benches
The deposit is white marble, worked in high benches that leave a tall, near-vertical wall behind each pass. The photographs in this article were taken during normal working hours: rails laid on the bench floor, machines tracked along them, control pedestals set back from the cut, and the wire running from the machine head around the guide pulleys and into the kerf.
Namibian conditions shape the equipment choice as much as the stone does. The ground is dry and dusty, the sunlight is strong, and the bench floor is uneven underfoot. Water is present at the cut — the slurry behind the machine is the visible sign of it — but it is managed carefully rather than used freely. In that setting, simple, robust machines with accessible service points matter more than a long feature list.

Running more than one machine along a face is normal where the bench is long enough: while one wire is cutting, the next kerf can be set up.
Why the 55kW class fits this bench
The 55kW class is the machine most quarries settle on for continuous block cutting. It carries enough power reserve to hold cutting speed through a long section without stalling in the cut, while staying practical on power supply and running cost.
That reserve is not about peak output. The failure mode in quarry wire sawing is a wire that slows down inside the cut: once it stops cutting and starts rubbing, the beads polish, the bond stops exposing diamond, and wire life collapses. A machine with reserve keeps the wire at speed when the load rises at the far end of a deep pass. In soft marble the wire is asked to run faster for longer, so the reserve is used continuously rather than occasionally.

Keeping that return run clear of the rails and cables is part of the daily setup, not an afterthought.
It also keeps the power supply realistic. A 55kW machine can be supported by the gen-sets and site supply that remote quarries actually run. Where block size and stone hardness justify it, the 75kW permanent-magnet machine is the next step up; for this bench, 55kW is the right size.
M002B diamond wire: specified for marble, not adapted to it
Marble wire is a different specification from granite wire. Soft, non-abrasive stone needs a harder bond, because the bond is what holds the diamond. A bond designed to self-sharpen in hard granite wears away rapidly in marble and takes the diamonds with it. M002B is the grade we specify for marble and limestone for exactly that reason: a harder bond formula that holds the diamond longer where the stone is soft and non-abrasive.
The assembly matters as much as the bead. Rubber or plastic coating is the norm for marble in both quarry and factory work — it protects the steel core, keeps bead spacing consistent, and suits the tighter pulley layouts used on bench machines. Sintered beads give the balance of cutting speed, bead life and cost per square meter that most marble producers are buying.
What we do not do is publish a wire life figure for someone else's quarry. Bead wear depends on stone variation, water quality, operator technique and how well the machine is aligned. The honest measure is cost per square meter of stone cut, tracked on site over months rather than quoted in advance.
Setting up on the bench
Most of the cutting quality is decided before the machine starts. The rail bed has to be level and straight along the line of the cut, because the machine tracks on it and any deviation shows up as a wandering kerf in a deep pass.
Pulley position sets the wire path. The wire should enter and leave the cut cleanly, without bearing on the kerf walls or rubbing the bench edge, and the return run should stay clear of the rails and power cables. Tension is set so the wire runs straight without bowing under load: too loose and the cut drifts, too tight and the core and coating take unnecessary stress.
Water goes to both the entry and the exit of the cut. Cooling at the kerf protects the bond and the coating, and flushing keeps slurry from packing around the beads. On a dry, dusty bench the water system deserves a daily check — a blocked nozzle is easy to miss and expensive to ignore.
The five-minute check before each shift:
- Rail joints tight, bed level, machine free to track the full cut length
- Pulleys turning freely, guards in place, wire seated correctly
- Wire tension checked cold, before the first pass
- Water reaching both the entry and the exit of the kerf
- Cables and control pedestal clear of the wire return run
What we watch in the first weeks
The first weeks tell you whether the specification is right. We look at four things, and none of them is a single number:
- Kerf straightness and cut deviation over the full depth of the pass
- Bead condition — polished or flattened beads mean the wire is rubbing, not cutting
- Wire stretch and coating wear where the wire runs over the pulleys
- Slurry — too thin means water is excessive, too thick means flushing is insufficient
What we ask for is a short record rather than an opinion: photographs of the beads, a note on where a cut drifted, and the hours logged on each wire. That is enough to adjust the next specification on evidence instead of assumption.
A note on figures: this article deliberately quotes no cutting speed, output or wire life for the Namibia project. The quarry keeps its own production records, we have not independently verified them, and we would rather describe the application honestly than publish a number we cannot stand behind.
Machine and wire are one system
The reason we supply the machine and the wire together is not packaging. Speed, tension and water are set by the machine, and they decide how the wire wears; the wire's bond decides how the machine's power is actually used. Specified separately, the two tend to be optimized against different assumptions.
For a quarry starting up, or changing stone, the sequence that works is: understand the deposit and the bench layout, match the machine class to block size and available power, then choose the wire for the stone and confirm the parameters on site. That order is slower at the start and faster over a year.
Working with KEENOVA
If you are cutting marble, or moving a wire saw into a new deposit, we can review your bench layout, power supply and stone with you before anything is specified. The starting point here is the 55kW wire saw machine and M002B diamond wire for marble; the specification follows your site.
Send us the stone type, bench height, block size and available power, and we will come back with a machine and wire match plus the parameters to start from. Photographs of an existing setup are just as useful as a specification sheet.
Contact our team to discuss your application, or read the technical notes on quarry wire sawing for the wider picture on machine and wire selection.